TIPS ABOUT HOW TO Extend Smok Pen Recharge Time

June 28, 2021 In Uncategorized

smok pen

TIPS ABOUT HOW TO Extend Smok Pen Recharge Time

The Smok Pen is really a new pen that was developed by two guys in California. They wished to create a cool writing instrument that looked like a real pen but had the ability to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has taken the marketplace by storm.

The Smok Pen includes a built quality that is just great. I found that even though it is an electronic pen the build quality is simply as good as any of the pens that I’ve reviewed. The reason being of how they made the very best cap. You don’t have to worry about the cap cracking or breaking on you Smok Valve Pen.

Both biggest differences that separate the Smok Valve from other pens may be the shape of the coils and just how that they are built. In general the coil on a Smok Pen is bigger than on other pens. I think that they did this deliberately, to make the pen feel bigger.

If you take a glance at a Smok Pen, you will observe that your body of the pen is round and not smooth like other pens. On the trunk of the pen you will find a little tab that houses the coil. When you press on the tab it is simple to turn the heating element on and off. I really liked this feature since it allows me to use the Smok Pen 22 whenever I feel like smoking.

To use the Smok Pen you must keep carefully the heat button pressed. Once the button is pressed, the heating element will begin to warm up. Once it gets to the appropriate temperature you can switch off the heating Puff Bar Flavors element. Smok recommends utilizing a 22mm tank. I prefer a more substantial tank, but that’s just me.

When you put your Smok Pen into the tank you will notice a indicator light seriously. The indicator light will remain green if you don’t put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is important to always put your pen into the charger before you apply the e-liquids to the coil heads. It is also important to do that before putting your e-liquids into the coil heads.

After you have completed this step, you should always check to see when you are at the proper temperature for the coils to fire. If not then you should turn the energy off and try again. If you are still not satisfied with your Smok Pen then I suggest you take it set for some troubleshooting. This is exactly what I’d call the “troubleshooting process” because sometimes things just usually do not work as they should. I would recommend that you perform the following two steps, then go on and check the Smok Pen to see if it still has the electronic charging port.

Prior to going any further you should take away the battery from your pen and unscrew the magnetic cap. You should then remove the plastic sleeve that holds the sub-ohm. You will find a wire that runs through the Smok’s body that is green in color. You should loosen this wire using pliers. When you have loosened this wire you can then access the sub-ohm. You need to then remove the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful never to touch the coils.

When you have placed the sub-ohm tank in to the pen you need to then place all of those other components like the wattage, the batteries and the heating element in to the included microwaveable microwave oven. Turn on the power and follow the on screen instructions. You should place the pen’s battery into the microwave and activate the setting. You need to then wait approximately 30 seconds before turning it back off. When you first put the pen into the microwave the electronic reading will show a minimal voltage protection setting. If this setting does not automatically get set then you should follow the on screen instructions.

After the Smok Pen has already reached the temperature that it needs to reach you need to then connect the two wires to the positive and negative on the positive post on the Smok unit. You need to then connect another end of the battery to the negative post on the negative side of the Smok unit. The final step would be to connect the positive cable to the bottom of the Smok’s on / off switch.

After all the components have been placed in to the pen, you should turn the power on. After the first test run, you should be able to see the battery life indicator light come on. If you don’t see any sign of life from the Smok Pen, you need to remove the battery from the pen and then replace it with a fresh one. For your convenience gleam green light which might be pressed so that you can confirm the battery charging status. Once you have done these things and you also do not start to see the green light indicating charging, you need to replace the battery.